Can you tell me how much shipping will cost for my order?
If you work through your order on the website, to the check out page, it will give you options for shipping and costs.
You do not have to purchase at this point, it can be used just for reference of shipping and handling cost.
Back to Top
I wish to buy xxxxxxxx
How can I order this, as it is not listed on your web site?
We strive to keep as many parts in stock as possible at all times, but we are often regulated by what the US distributor has in stock and how many, we try to not list parts that we cannot get a consistent supply of.
Often we can get these parts as a special order. Which depending on your requirements may take considerable time and may hold up your original order if you have one.
Back to Top
I ordered a part from your web site because there was no indication that it was not in stock.
Why do you continue to allow people to buy parts that are not in stock?
When are we supposed to know when it will be in stock?
We always try to maintain correct stock control, but sometimes due to unforeseen circumstance the websites stock quantities may differ.
We strive to get replacement parts as quick as possible and are sorry if there is a delay in shipping your part.
If we do not have the part in stock and have no accurate idea of when we will have it, we normally cancel the item and refund the cost.
I you wish we can hold the complete order until we have all the parts but there is no guarantee on time frame if you choose this option, please add this request to your notes when ordering
Back to Top
I want to replace the standard front sight on my CZ pistol with a Fiber Optic front sight.
I do not wish to replace the rear sight. What size do I need?
CZ factory pistols (exception is the TS which come with 7.5mm and Kadet which comes with 6.5mm High) are fitted with a 5.5mm High front sight (when measured from the bottom of the sight to the top of the sight, with the sight OUT of the slide).
So the correct sight for a factory gun would be any 5.5mm replacement sight we sell.
(Unless it is TS or Kadet)
Back to Top
Can you ship Hi Capacity magazines to a state that has a capacity restriction? If not, can you strip the magazine into component parts and ship them separately?
Simple answer is no, we have to comply with all federal and state laws.
Back to Top
I'm looking for a firearm that is on the California Department Of Justice(CA DOJ) handgun Roster; can you ship 2 10round magazines instead of the Hi Capacity magazines?
No problem, the law does not allow us the ship Hi Capacity magazine to certain states so we always swap the magazines for the appropriate legal magazine.
Back to Top
Is there any way to convert a non-decocker to a decocker?
No, the cuts in the frame are different.
Back to Top
I have a decocker style factory pistol, is there anyway to convert it to Single Action Only?
Unfortunately it is not possible, if this was done the pistol would not have a manual safety so it would not be safe in the SA Only mode.
Back to Top
I have a CZ 75 pistol with a creepy, hard and mushy trigger. Would the 85 trigger installed by you and tuned, take care of this otherwise superb pistol?
No the 85 combat trigger will make no difference to the trigger pull on the gun, having a trigger job which includes the Comp hammer, fitted will take care of this
http://czcustom.com/sanditriggerworksada.aspx
Back to Top
Can you supply your SP-01 shadow with 5", Similar to the guns shipped to Australia and Denmark?
Sorry No. We have tried to get these barrels from CZUB but as yet have not been able to purchase them.
Back to Top
I have heard that the Kadet conversion kit will not fit the 75B Omega.
What is the specific reason for this?
The firing pin lifter on the Omega and P07 are different configuration and the slot in the slide of the Kadet does not allow for this, so you cannot physically put the slide onto either the Omega or the Kadet
Back to Top
Firing pin blocks on CZ Pistols
As of this moment the only CZ pistols that are not fitted with firing pin blocks are:
CZ 75 Sp01 Shadow
CZ 85 Combat
CZ Tactical Sports
All other have firing pin block fitted
the B designation in the nomenclature on the slide
I.E. CZ75B indicates the presence of the firing pin block.
Back to Top
Does xxxxxx part fit my EAA / Tangfolgio pistol?
So far we have ascertained that almost no parts interchange without substantial re profiling and fitting.
EAA / Tangfolgio seem to have chosen to create there clone with completely different measurement on almost all parts
Back to Top
I was hoping you could tell me if the CZ P-01 and CZ compact (steel frame) have the same internal components or if they are different, requiring different replacement parts?
The P01 is a Decoker and the Compact is an SA DA gun, some parts will interchange, but nothing from the internal fire mechanism, except the trigger.
Back to Top
I am looking for a part on your website, which I know was originally there. Did you stop selling this part?
We always try to maintain correct stock control, but sometimes due to unforeseen circumstance the websites stock quantities may differ.
Sometimes when we do not have a part, we find it necessary to switch the product off, so it cannot be purchased, we obviously try not to do this and prefer for it to reclassify itself as out of stock.
Back to Top
Is it possible to fit the CZ TS Extended Ambi Safety LHS (Item Number: 10226) on the SP01 Shadow?
No, there is a specific part for the CZ 75 Shadow, which actually will fir in several other models of CZ 75.
The boss and the spindle on the TS safety are both longer, to accommodate the wider frame of the Tactical Sports (TS)
Back to Top
I am interested in buying a CZ 75 SP-01 Tactical in .40 S&W
I was wondering if you guys do any custom work on this pistol? I am mostly interested in improving the trigger.
Sure we can complete any custom work on new guns before we ship (assuming it is legal in your state I.E. California)
This is a great way to improve you gun and save some money on shipping.
Back to Top
Are you going to have the CZEHMATE available
here in the US to purchase?
CZ USA have had these guns on order from CZ UB for the last 2 years, as soon as we have information we will post on the web site
Back to Top
Fitting a CZ Front Sight
Fitting Front Sight
Remove the roll pin using the appropriate punch http://czcustom.com/czpunch.aspx
Tap the old front sight out (towards the muzzle) using an appropriate soft hammer or soft block
Replace the new front sight into the dovetail and tap it toward the back of the gun until it seats in the rear of the dovetail cut. Make sure it goes all the way back.
Using the correct drill, http://czcustom.com/CZ_Front_Sight_Drill.aspx
Drill through the roll pin hole (IMPORTANT) Drill from the left side of the gun to the right side, Drill cut clockwise and drilling from this direction will not cause the front sight to walk out as the drill starts to cut.
Replace the front sight pin, new pins are available http://czcustom.com/czfrontsightpin.aspx
Back to Top